Chapter 1 INTRODUCTION - TM-10-4510-201-140033
Figure 1-1. Bath unit set up for operation.
Tabulated Data - TM-10-4510-201-140035
Figure 1-2. Bath unit instruction plate.
Chapter 2 OPERATING INSTRUCTIONS - TM-10-4510-201-140037
Installation cont'd
Figure 2-2. Removing suction hose strainer from exhaust duct.
Figure 2-3. Removing shower stand legs from exhaust duct.
Figure 2-4. Suction hose assembly and shower stand risers on baseboard.
Figure 2-5. Baseboard retaining brackets.
Figure 2-6. Methods of positioning strainer in water source.
Figure 2-7. Water pump and hose assemblies and cable connected.
Figure 2-8. Hoses connected to water heater and fuel drum.
Figure 2-9. Hoses connected to heater manifold.
Figure 2-10. Connecting water hose assembly to shower stand adapter.
Section II. MOVEMENT TO A NEW WORKSITE
Instruments
Figure 2-11A. Bath unit controls and instruments (sheet 1 of 5).
Figure 2-11B. Bath unit controls and instruments (sheet 2 of 5)
Figure 2-11C. Bath unit controls and instruments (sheet 3 of 5)
Figure 2-11D. Bath unit controls and instruments (sheet 4 of 5)
Section IV. OPERATION UNDER USUAL CONDITIONS
Figure 2-12. Water pump assembly.
Starting Bath Unit
Figure 2-13. Water heater, left end view
Section V. OPERATION UNDER UNUSUAL CONDITIONS
Fire Extinguisher - TM-10-4510-201-140059
Chapter 3 OPERATOR'S MAINTENANCE INSTRUCTIONS
Table 3-1. Preventive Maintenance Checks and Services.
Section IV. TROUBLESHOOTING - TM-10-4510-201-140063
Section V. MAINTENANCE OF MISCELLANEOUS ITEMS - TM-10-4510-201-140064
Figure 3-1. Suction strainer
Figure 3-2. Suction hose.
Section VI. MAINTENANCE OF SHOWER STAND AND WATER PUMP
Figure 3-4. Shower head nozzle (used on Army models SPE 35 and SPE 35A) disassembled
Water Line Strainer
Figure 3-6. Water line strainer.
Chapter 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Unpacking Bath Unit
Section III. ORGANIZATIONAL PREVENTIVE MAINTENANCE CHECKS AND SERVICES
Table 4-1. Preventive Maintenance Checks and Services.
Section IV. TROUBLESHOOTING - TM-10-4510-201-140075
PULSATING PRESSURE INDICATED ON'GAGE
Section V. MAINTENANCE OF MISCELLANEOUS ITEMS - TM-10-4510-201-140077
Figure 4-3. Generator receptacle box with cable.
Figure 4-4. Wiring diagram of generator receptacle box.
Baseboard
Figure 4-5. Bath unit baseboard and straps.
Section VI. MAINTENANCE OF' SHOWER STAND ASSEMBLY
Riser
Section VII. MAINTENANCE OF WATER PUMP ASSEMBLY
Figure 4-9. Strainer element, removed from water line strainer.
Figure 4-10. Water pump assembly, left-side view.
Figure 4-11. Water pump electrical connections.
Water Pump Electric Motor
Figure 4-13. Vane plate mounted on pump bracket.
Figure 4-14. Water pump, disassembled.
Figure 4-15. Wiring diagram for water pump.
Water Pump - TM-10-4510-201-140092
Figure 4-16. Circuit breaker subassembly showing wire connections.
Figure 4-17. Circuit breaker subassembly cover opened to show overload heaters.
Section VIII. MAINTENANCE OF WATER HEATER ASSEMBLY
Figure 4-19. Schematic drawing of burner fuel system.
Figure 4-20. Barrel plug and fuel hose assemblies
Figure 4-21. Water heater, bottom view.
Figure 4-22. Water heater control panel box and gages.
Figure 4-23. Wiring diagram for water heater.
Figure 4-24. Water heater skid and skid level.
Figure 4-25. Boiler box cover and gasket, removal and installation.
Burner Assembly
Servicing
Figure 4-26. Water heater, left-end view.
Figure 4-27. Electrodes and holder, removed from burner assembly.
Figure 4-29. Burner head removed from water heater.
Figure 4-30. Burner electrode spark gap adjustment.
Pressure Relief Valve Overflow Tube and Clip
Figure 4-32. Water heater pressure and temperature control with cover removed.
Bypass Hose
Shower Stand Control and Water Blender Valves
Welded Tank
Bath Unit Instructional Plate
Figure 4-36. Water heater control panel box with cover removed.
Water Heater Pressure and Temperature Control
Figure 4-37. Installation of York-Shipley pressure and temperature control
Water Heater Burner Solenoid Valve.
Fuel Pump Assembly
Figure 4-38. Fuel pump and filter mounted on blower.
Figure 4-39. Adjusting pressure on fuel pump.
Fuel Pump Strainer and Cover Gasket.
Figure 4-40. Fuel pump, strainer removed.
Figure 4-41. Filter head, removing fuel filter head gasket.
Figure 4-42. Blower, disassembled.
Fuel Fittings and Lines
Blower Shutter Assembly
Inspection - TM-10-4510-201-140128
CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE SUPPORT
General Cleaning Instructions
CHAPTER 6 REPAIR OF MISCELLANEOUS ITEMS, SHOWER STAND AND PUMP ASSEMBLY, AND WATER HEATER ASSEMBLY
Figure 6-1. Fabrication details for baseboard.
Section II. SHOWER STAND AND PUMP ASSEMBLY
Figure 6-2. Schematic drawing of test procedures for transformer.
Skid and Bail Handle
Figure 6-3A. Pressure and temperature control (Used on all Army models except SPE 45) (sheet 1 of 2).
Figure 6-3B. Pressure and temperature control (Used on all Army models except SPE 45) (sheet 2 of 2).
Figure 6-4. Pressure and temperature control
Figure 6-5. Altitude variations graph
Figure 6-6. Fuel pump, disassembled.
Blower and Fuel Pump Electric Motor
Figure 6-7. Water heater blower and fuel pump motor, disassembled.
Electrical Conduit
Chapter 7 ADMINISTRATIVE STORAGE
Inspection and Maintenance of Equipment in Storage
Appendix A REFERENCES - TM-10-4510-201-140147
Appendix B MAINTENANCE ALLOCATION CHART (MAC) - TM-10-4510-201-140149
The Army Maintenance System MAC
The Army Maintenance System MAC cont'd
Explanation of Columns in the Tools and Test Equipment Requirements, Section III
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD cont'd - TM-10-4510-201-140154
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD cont'd - TM-10-4510-201-140155
Section III. TOOLS AND TEST EQUIPMENT
APPENDIX C BASIC ISSUE ITEMS LIST AND ITEMS TROOP INSTALLED OR AUTHORIZED LIST
Federal Stock Number - TM-10-4510-201-140158
TM-10-4510-201-14 - index
Figure 1-1. Bath unit set up for operation.
Tabulated Data - TM-10-4510-201-140035
Figure 1-2. Bath unit instruction plate.
Chapter 2 OPERATING INSTRUCTIONS - TM-10-4510-201-140037
Installation cont'd
Figure 2-2. Removing suction hose strainer from exhaust duct.
Figure 2-3. Removing shower stand legs from exhaust duct.
Figure 2-4. Suction hose assembly and shower stand risers on baseboard.
Figure 2-5. Baseboard retaining brackets.
Figure 2-6. Methods of positioning strainer in water source.
Figure 2-7. Water pump and hose assemblies and cable connected.
Figure 2-8. Hoses connected to water heater and fuel drum.
Figure 2-9. Hoses connected to heater manifold.
Figure 2-10. Connecting water hose assembly to shower stand adapter.
Section II. MOVEMENT TO A NEW WORKSITE
Instruments
Figure 2-11A. Bath unit controls and instruments (sheet 1 of 5).
Figure 2-11B. Bath unit controls and instruments (sheet 2 of 5)
Figure 2-11C. Bath unit controls and instruments (sheet 3 of 5)
Figure 2-11D. Bath unit controls and instruments (sheet 4 of 5)
Section IV. OPERATION UNDER USUAL CONDITIONS
Figure 2-12. Water pump assembly.
Starting Bath Unit
Figure 2-13. Water heater, left end view
Section V. OPERATION UNDER UNUSUAL CONDITIONS
Fire Extinguisher - TM-10-4510-201-140059
Chapter 3 OPERATOR'S MAINTENANCE INSTRUCTIONS
Table 3-1. Preventive Maintenance Checks and Services.
Section IV. TROUBLESHOOTING - TM-10-4510-201-140063
Section V. MAINTENANCE OF MISCELLANEOUS ITEMS - TM-10-4510-201-140064
Figure 3-1. Suction strainer
Figure 3-2. Suction hose.
Section VI. MAINTENANCE OF SHOWER STAND AND WATER PUMP
Figure 3-4. Shower head nozzle (used on Army models SPE 35 and SPE 35A) disassembled
Water Line Strainer
Figure 3-6. Water line strainer.
Chapter 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Unpacking Bath Unit
Section III. ORGANIZATIONAL PREVENTIVE MAINTENANCE CHECKS AND SERVICES
Table 4-1. Preventive Maintenance Checks and Services.
Section IV. TROUBLESHOOTING - TM-10-4510-201-140075
PULSATING PRESSURE INDICATED ON'GAGE
Section V. MAINTENANCE OF MISCELLANEOUS ITEMS - TM-10-4510-201-140077
Figure 4-3. Generator receptacle box with cable.
Figure 4-4. Wiring diagram of generator receptacle box.
Baseboard
Figure 4-5. Bath unit baseboard and straps.
Section VI. MAINTENANCE OF' SHOWER STAND ASSEMBLY
Riser
Section VII. MAINTENANCE OF WATER PUMP ASSEMBLY
Figure 4-9. Strainer element, removed from water line strainer.
Figure 4-10. Water pump assembly, left-side view.
Figure 4-11. Water pump electrical connections.
Water Pump Electric Motor
Figure 4-13. Vane plate mounted on pump bracket.
Figure 4-14. Water pump, disassembled.
Figure 4-15. Wiring diagram for water pump.
Water Pump - TM-10-4510-201-140092
Figure 4-16. Circuit breaker subassembly showing wire connections.
Figure 4-17. Circuit breaker subassembly cover opened to show overload heaters.
Section VIII. MAINTENANCE OF WATER HEATER ASSEMBLY
Figure 4-19. Schematic drawing of burner fuel system.
Figure 4-20. Barrel plug and fuel hose assemblies
Figure 4-21. Water heater, bottom view.
Figure 4-22. Water heater control panel box and gages.
Figure 4-23. Wiring diagram for water heater.
Figure 4-24. Water heater skid and skid level.
Figure 4-25. Boiler box cover and gasket, removal and installation.
Burner Assembly
Servicing
Figure 4-26. Water heater, left-end view.
Figure 4-27. Electrodes and holder, removed from burner assembly.
Figure 4-29. Burner head removed from water heater.
Figure 4-30. Burner electrode spark gap adjustment.
Pressure Relief Valve Overflow Tube and Clip
Figure 4-32. Water heater pressure and temperature control with cover removed.
Bypass Hose
Shower Stand Control and Water Blender Valves
Welded Tank
Bath Unit Instructional Plate
Figure 4-36. Water heater control panel box with cover removed.
Water Heater Pressure and Temperature Control
Figure 4-37. Installation of York-Shipley pressure and temperature control
Water Heater Burner Solenoid Valve.
Fuel Pump Assembly
Figure 4-38. Fuel pump and filter mounted on blower.
Figure 4-39. Adjusting pressure on fuel pump.
Fuel Pump Strainer and Cover Gasket.
Figure 4-40. Fuel pump, strainer removed.
Figure 4-41. Filter head, removing fuel filter head gasket.
Figure 4-42. Blower, disassembled.
Fuel Fittings and Lines
Blower Shutter Assembly
Inspection - TM-10-4510-201-140128
CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE SUPPORT
General Cleaning Instructions
CHAPTER 6 REPAIR OF MISCELLANEOUS ITEMS, SHOWER STAND AND PUMP ASSEMBLY, AND WATER HEATER ASSEMBLY
Figure 6-1. Fabrication details for baseboard.
Section II. SHOWER STAND AND PUMP ASSEMBLY
Figure 6-2. Schematic drawing of test procedures for transformer.
Skid and Bail Handle
Figure 6-3A. Pressure and temperature control (Used on all Army models except SPE 45) (sheet 1 of 2).
Figure 6-3B. Pressure and temperature control (Used on all Army models except SPE 45) (sheet 2 of 2).
Figure 6-4. Pressure and temperature control
Figure 6-5. Altitude variations graph
Figure 6-6. Fuel pump, disassembled.
Blower and Fuel Pump Electric Motor
Figure 6-7. Water heater blower and fuel pump motor, disassembled.
Electrical Conduit
Chapter 7 ADMINISTRATIVE STORAGE
Inspection and Maintenance of Equipment in Storage
Appendix A REFERENCES - TM-10-4510-201-140147
Appendix B MAINTENANCE ALLOCATION CHART (MAC) - TM-10-4510-201-140149
The Army Maintenance System MAC
The Army Maintenance System MAC cont'd
Explanation of Columns in the Tools and Test Equipment Requirements, Section III
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD cont'd - TM-10-4510-201-140154
Section II. MAINTENANCE ALLOCATION CHART FOR BATH UNIT, PORTABLE, 8-SHOWER HEAD cont'd - TM-10-4510-201-140155
Section III. TOOLS AND TEST EQUIPMENT
APPENDIX C BASIC ISSUE ITEMS LIST AND ITEMS TROOP INSTALLED OR AUTHORIZED LIST
Federal Stock Number - TM-10-4510-201-140158
TM-10-4510-201-14 - index
