TM 5-6350-255-13
Table 5-2. BINARY TO IDENTIFICATION NUMBER CONVERSION
TABLE AND PARITY TABLE (Cont'd)
Bits
Bits
ID
1
2
3
4
5
6
Parity
ID
1
2
3
4
5
6
Parity
No.
No
4
0
1
1
0
0
1
0
26
1
1
1
0
1
1
0
5
0
1
1
0
1
0
0
7
1
1
1
1
0
1
0
6
0
1
1
0
1
1
1
28
I
1
1
1
1
0
0
7
0
1
1
1
0
1
1
29
1
1
1
1
1
1
1
8
0
1
1
1
1
0
1
31
0
0
0
1
0
1
1
9
0
1
1
1
1
1
0
32
0
0
0
1
1
0
1
11
1
0
0
1
0
1
0
33
0
0
0
1
1
1
0
12
1
0
0
1
1
0
0
34
0
0
1
0
0
1
1
13
1
0
0
1
1
1
1
35
0
0
1
0
1
0
1
14
1
0
1
0
0
1
0
36
0
0
1
0
1
1
0
15
1
0
1
0
1
0
0
37
0
0
1
1
0
1
0
16
0
1
0
1
1
1
1
38
0
0
1
1
1
0
0
17
1
0
1
1
0
1
1
39
0
0
1
1
1
1
1
18
1
0
1
1
1
0
1
41
0
1
0
0
0
1
1
19
1
0
1
1
1
1
0
42
0
1
0
0
1
0
1
21
1
1
0
1
0
1
1
43
0
1
0
0
1
1
0
22
1
1
0
1
1
0
1
44
1
0
0
0
0
1
1
45
1
0
0
0
1
0
1
58
1
1
1
0
0
0
0
46
1
0
0
0
1
1
0
59
1
1
1
1
0
0
1
47
1
1
0
0
0
1
0
61
0
0
0
0
0
1
0
48
1
1
0
0
1
0
0
62
0
0
0
0
1
0
0
49
1
1
0
0
1
1
1
63
0
0
0
0
1
1
1
51
0
1
0
1
0
0
1
64
0
0
0
1
0
0
0
52
0
1
1
0
0
0
1
65
0
0
1
0
0
0
0
53
0
1
1
1
0
0
0
66
0
0
1
1
0
0
1
54
1
0
0
1
0
0
1
67
0
1
0
0
0
0
0
55
1
0
1
0
0
0
1
68
1
0
0
0
0
0
0
56
1
0
I
1
0
0
0
69
1
1
0
0
0
0
1
57
1
1
0
1
0
0
0
71
0
0
0
0
0
0
1
Section III. ASSEMBLY AND CHECKOUT
5-4. Installation of MINISID III Modules
5-5. Code Plug
a. Remove MINISID III SCUE (Sensor Case
a. Removal. With the open end of the short tube
Unique Electronics or MINISID III without common
facing you, tilt the case downward causing the code plug
modules) from its packing container.
assembly to slide forward. Remove and discard packing
material (fig. 5-3). Do not remove doughnut shaped
foam spacer at bottom of tube. Fold out code plug from
CAUTION
the case as far as the flat cable assembly will permit with
Depress safety spring (fig. 5-2) and set
the multicolored surface up.
power switch to OFF position.
5-6. Code Plug Unique Setable Assembly
a. The following parameters are set on the code
b. The antenna and transmitter cap assembly is
plug, ID for AN/GSQ-154 (V) (fig. 5-9) (or CID when
equipped with a setscrew that locks this cap to the case
used with ancillary equipment, for Model AN/GSQ154A
assembly to prevent unnecessary field opening of the
(V)); Code Parity, Bit Rate, and Gain. Code plug setting
case. This setscrew must be loosened before removing
is accomplished by installing a horseshoe shaped jumper
the cap assembly. The two caps must be removed from
the case assembly by a counterclockwise movement to
assembly.
disengage the bayonet lock. Remove antenna and
transmitter cap assembly (fig. 5-3) from the end of the
short tube.
5-11
