TB 10-8400-252-23
i. Coveralls, Safety, Protective, Specification MIL-C-43570.
Finished Measurements (In Inches)
Size
X-Small
Small
Medium
Large
X-Large
XX-Large
Tolerance
1/2 Chest1
20 1/2
22 1/2
24 1/2
26 1/2
28 1/2
30 1/2
1/2
1/2 Waist2
17
19
21
23
25
27
1/2
Sleeve inseam3
23
23
23
23
23
23
1/2
Leg inseam4
32
32
32
32
32
32
1/2
1
The coverall shall be buttoned smooth and flat and measured across the front from base of armhole to base of armhole.
2
The coverall shall be buttoned smooth and flat and measured across waist from side seam to side seam.
3
The sleeve inseam shall be measured from the base of armhole along inseam to bottom of sleeve hem.
4
The leg inseam shall be measured from crotch seam along inseam to bottom of leg hem.
j. Coveralls, Toxicological Agents, Protective, Specification MIL-C-2181.
Finished Measurements (In Inches)
Small
Medium
Large
Tolerance
1
1/2 breast
27
29
31
1/2
2
1/2 waist
21
23
25
1/2
3
Sleeve inseam
22 1/2
22 3/4
24
1/2
4
Trouser inseam
31
32
32
1/2
1
With the slide fastener closed, and front of coverall smoothed flat, measure across front of coat part from a point - inch below armhole seam from side
seam to side seam.
2
With the slide fastener closed, and front of coverall smoothed flat, measure across waist from side fold to side fold.
3
Measure the sleeve inseam from the base of armhole along the inseam of sleeve to bottom of sleeve.
4
Measure from the base of crotch along the inside of leg to the bottom of leg.
7. Hood, Armored, Vehicle, Crewman, Specification LP/P DES 30-68.
Finished Measurements (In Inches)
Overall width
Crown height
Tolerance
35 1/2
17 1/2
1/2
1
With hood open, measure from end to end in a straight line along bottom of hood.
2
With hood folded and bottom edges even, measure from top of crown to the bottom edge In a straight line. 8 inches from side joining seam at the bottom
edge.
8. Jackets.
a. Jacket, Flying, Men's, Specification MIL-J-6278E.
Finished Measurements (In Inches)
Measurement*
Size
Tolerance
Small
Medium
Large
Extra large
Extra extra large
Plus
Minus
Back length
21 1/2
22
22 1/4
23 1/4
23 1/4
3/8
1/2
1/2 chest
23
25
27
29
32 1/2
1/2
1/2
1/2 bottom
21 1/4
23 1/4
25 1/4
27 1/4
29 1/4
1/2
1/2
Sleeve inseam
16 1/4
16 1/2
16 3/4
17
17 1/4
1/2
3/8
*NOTE
(a) The measurement of the back length shall be taken at the center of the back from the bottom of undercollar seam to the bottom above the knit
(b) The measurement of the 1/2 chest shall be taken with the slide fastener closed from folded edge to folded edge at the base of the armhole.
(c) The measurement of the 1/2 Bottom shall be taken with the slide fastener closed from folded edge to folded edge at the bottom above the knit,
or the measurement may be taken with the jacket unfastened and spread open from end to end at slide fastener at the bottom of the knit.
(d) The measurement of the sleeve inseam shall be taken along the underarm seam, from the armhole to the seam above the knit
11
