TM 10-3510-208-12
(10) Install the door lock handle support (15)
and secure it with rivets (14).
(11) Install the door catch (13) and secure it
Clean all parts in a well-ventilated area.
Avoid inhalation of solvent fumes and
with stud (12).
prolonged exposure to akin to cleaning
(12) Install the door handle support (11) and
solvent. Wash exposed skin thoroughly.
secure it with rivets (10).
Dry cleaning solvent (Fed. Spec. P-D-680)
(13) Install the door handle (9) and secure it
used to clean parts is potentially dangerous
with stud (8) .
to personnel and property. Do not use near
(14) Install the door latch link (7), and secure
open flame or excessive heat. Flash point
it with pins (3 and 6), flatwashers (2 and 5) and
of solvent is 100 to 138F. (38 to 59C.).
cotter pins (1 and 4).
(15) Connect all wiring and lines to the washer
Clean all metal parts of the washer door
door assembly.
assembly using cleaning solvent, Fed. Spec.
P-D-680, and dry thoroughly. Clean door glass
4-75. Valve Drain Assembly
and seal with mild soap and water and dry
a. Removal.
thoroughly.
c. Inspection.
and remove tubing (2) and nut (3).
(1) Inspect the head sheet, door latch link,
(2) Disconnect tube assembly (4) and remove
and door for cracks, dents, burrs and other
tubing (5) and nut (6).
damage.
(3) Remove elbow)(7).
(2) Inspect the door glass for breaks, cracks
(4) Remove adapter (8).
and Chips.
(5) Remove cotter pin (9) and straight pin
(3) Inspect the gaskets for tears, pits, cracks
(lo).
and excessive wear.
(6) Loosen nut (12) and remove lever (11);
(4) Inspect all hardware for thread damage.
disassemble by removing nut (12) and knob (13)
d. Repair.
from lever.
(1) Repair or replace a damaged head sheet,
(7) Remove nuts (14), washers (15) and screws
door latch link or door.
(16) securing the support and remove support (17).
(2) Replace a damaged gasket or door glass
-
(8) Remove screws (18) and washers (19)
and all missing or damaged hardware.
securing the housing; removing housing (20) and
e. Assembly and Installation.
housing gasket (21).
(9) Slip the support (22) off the shaft.
(43) . Secure sheet with screws (42) .
(10) Pull taper pin (23) from the dog, and slip
(2) Install seal (41), gasket (40), and clamps
dog (24) from the shaft.
(39).
(11) Remove the screws (25) and washers (26)
(3) Install glass (38), gasket (37), clamp (36),
securing the housing cover to the housing, and
and screws (35) on door.
remove cover (27) and cover gasket (28).
(4) Position the bracket (34) on the sheet and
(12) Pull out tpaer pin (29) freeing lever (30);
secure it with rivets (33).
remove setscrew (31) from lever.
(5) Reassemble the door assembly (28). Install
(13) Pull taper pin (32) from lever and remove
door (32) and secure it with lockwasher (31) and
lever (33) from shaft (34).
screw (30). Install bushing (29).
(14) Remove setscrew (35), nut (36), screw
(6) Install straight pin (27) and secure it with
(37) and washer (38).
cotter pin (26).
(15) Remove straight pin (39) from the
(7) Assemble the switch (25) to the sheet.
bracket; separating bracket (40) and air cylinder
assembly (41).
locknut (22) and elbow (21).
(8) Install connector (20) and conduit (19).
(9) Install cylinder (18) on sheet and secure it
with washers (17) and screws (16).
4-138