TM 5-6350-255-13
APPENDIX C.
REPAIR PARTS
Section I. INTRODUCTION
PG
Item procured and stocked to provide for
C-1. Scope
sustained support for life of the equipment It
a. This section lists repair parts, required for the
is applied to an item peculiar to the
performance of organizational and direct support maintenance
equipment which, because of probable
of the MINISID III.
discontinuance or shutdown of production
b. Repair parts listed represent those authorized for use
facilities, would prove uneconomical to
at indicated maintenance levels and will be requisitioned on an
reproduce at a later date.
"as required" basis until stockage is justified by demand in
KD
An item of depot overhaul/repair kit and not
accordance with AR 710-2.
purchased separately.
C-2. General
KF
An
item of a maintenance kit and not
This Repair Parts list is divided into the following sections:
purchased separately.
a. Prescribed Load Allowance List, Section II (Not
KB
Item included in both a depot overhaul/repair
applicable).
kit and a maintenance kit.
b. Repair Parts List, Section II. A list of repair parts
MO
Item to be manufactured or fabricated at
authorized at the organizational and direct support level for
organizational level.
performance of maintenance. The list also includes parts
MF
Item to be manufactured or fabricated at
which must be removed for replacement of the authorized
direct support maintenance level.
parts. Parts lists are composed of assembly groups in
MH
Item to be manufactured or fabricated at
ascending numerical sequence, with the parts in each group
general support maintenance level.
listed in figure and item number sequence.
MD
Item to be manufactured or fabricated at
C-3. Explanation of Columns
depot maintenance level.
The following provides an explanation of columns found in the
AO
Item to be assembled at organizational level.
tabulated listings in Section III.
AF
Item to be assembled at direct support
a. Source, Maintenance, and Recoverability Codes
maintenance level.
(SMR). The SMR code is a five letter code composed of three
AH
Item to be assembled at general support
parts consisting of a two (2) position source code, a two (2)
maintenance level.
position maintenance code, and a one (1) position
AD
Item to be assembled at depot maintenance
recoverability code. Support items listed in the RPSTL
level.
assigned maintenance and recoverability codes and no
XA
Item
is NOT procuredor
stocked
source code can be requisitioned, with justification, through
because the requirements for the item will
normal supply channels by use of the manufacturer's code and
result in replacement of the next higher
part number. Such support items are NOT normally stocked.
assembly.
(1)Source Code. Indicates the manner of acquiring
XB
Item NOT procured or stocked
If
support items for maintenance, repair, or overhaul of end
available through salvage requisition.
items. Source codes are entered in the first and second
XC
Installation drawing, diagram, instruction
positions as follows:
sheet, or field service drawing that is
Code
Definition
identified by manufacturer's part number.
PA
Item procured and stocked for anticipated or
XD
A low mortality item that is not stocked
known usage.
When required, items will be requested and
PB
Item procured and stocked for insurance
provided through normal supply channels.
purposes because essentiality dictates that
NOTE
a minimum quantity be available in the
Cannibalization or salvage may be used as a
supply system.
source of supply for any items coded above except
PC
Item procured and stocked and which
those coded XA or XD.
otherwise would be coded PA except that it
(2) Maintenance Code. Maintenance are assigned to
is deteriorative in nature.
indicate the levels of maintenance authorized to use and repair
PD
Support item, excluding support equipment,
support items. The maintenance codes are entered in the
procured for initial issue or outfitting and
third and fourth positions of the Uniform SMR Code format as
stocked only for subsequent or additional
follows:
initial issues or outfittings. NOT subject to
(a) The maintenance code entered in the third position
automatic replenishment.
will indicate the lowest maintenance level authorized to
Code
Definition
remove, replace, and use the support item. The maintenance
PE
Support equipment procured and stocked for initial
code entered in the third position will indicate one of the
issue or outfittings to specified maintenance repair
following levels of maintenance:
activities.
PF
Support equipment which will not be stocked
but which will be centrally procured on
demand.
C-1
