TM 10-3510-208-12
(a) Tag and disconnect leads from the
the following instructions to remove the extract
signal switch.
switch.
(b) Remove the screws and washers
(a) Tag and disconnect leads from the
securing the nameplate to the control box.
extract switch.
(c) Remove the nameplate.
(b) Remove the locking nut securing the
(d) Remove the screws securing the signal
extract switch to the control box.
switch to the control box.
(c) Remove the extract switch.
(e) Remove signal switch.
(2) Installation.
(2) Installation.
(a) Position the extract switch in place and
(a) Position signal switch in place on the
secure with locking nut.
control box.
(b) Reconnect leads to the extract switch.
(b) Secure with screws.
h. Hot Water Switch.
(c) Position nameplate in place on the
(1) Removal. Refer to figure 4-90 or 4-91 end
control box.
the following instructions to remove the hot water
(d) Secure with washers and screws.
switch .
(a) Tag and disconnect leads from the hot
(e) Reconnect leads to the signal switch.
k. Reversing Timer.
water switch.
(b) Remove the screws and washers
securing the nameplate to the control box.
the following instructions to remove the reversing
timer .
(c) Remove the nameplate.
(a) Tag and disconnect leads from the
(d) Remove the screws securing the hot
reversing timer.
water switch to the control box.
(2)) Remove the screws and washers
(e) Remove the hot water switch.
securing the reversing timer to the control panel.
(2) Installation.
(c) Remove the reversing timer.
(a) Position the hot water switch in place on
(2) Installation.
the control box.
(a) Position the reversing timer in place on
(b) Secure with screws.
the control panel.
(c) Position the nameplate in plain on the
(b) Secure with washers and screws.
control box.
(c) Reconnect leads to the reversing timer.
(d) Secure with washers and screws.
l. Terminal Block.
(e) Reconnect leads to the hot water switch.
i. Cold Water Switch.
(1) Removal. Refer to figure 4-90 or 4-91
the following instructions to remove the terminal
and the following instructions to remove the cold
block.
(a) Tag and disconnect leads from the
water switch.
terminal block.
(a) Tag and disconnect leads from the cold
(b) Remove the screws and washers that
water switch.
secure the terminal block to the control panel.
(b) Remove the screws and washers
(c) Remove the terminal block.
securing the nameplate to the control box.
(2) Installation.
(c) Remove the nameplate.
(a) Position the terminal block in place on
(d) Remove the screws securing the cold
the control panel.
water switch to the control box.
(b) Secure with washers and screws.
(e) Remove the cold water switch.
(c) Reconnect leads to the terminal block.
(2) Installation.
m. Extractor Starter.
(a) Position the cold water switch in place
(1) Removal. Refer to figure 4-90 or 4-91 and
on the control box.
the following instructions to remove the extractor
(b) Secure with screws.
starter.
(c) Position the nameplate in place on the
(a) Tag and disconnect leads from the
control box.
extractor starter.
(d) Secure with washers and screws.
(b) Remove the screws and washers that
(e) Reconnect leads to the cold water
secure the extractor starter to the control panel.
Switch.
(c) Remove the extractor starter.
j. Signal Switch.
(2) Installation.
(1) Removal. Refer to figure 4-90 or 4-91 and
(a) Position the extractor starter in place on
the following instructions to remove the signal
the control panel.
switch,
4-127
