TM 10-8400-203-23
27-24 Change 11
i.
Miscellaneous Items
ITEM (NSN)
SIZES
SPECIFICATION
Waistbelt, FLC Assembly (Part of 8465-01-465-2056)
One Size
PD-02-02
Adapter, ALICE, Clip (8465-01-465-2062)
One Size
PD-02-02
Set, Buckles (8465-01-465-2080)
One Size
PD-02-02
Strap, Lashing (8465-01-465-2095)
One Size
PD-02-02
Adapter, K-BAR (8465-01-465-2272)
One Size
PD-02-02
The utility belt is constructed of two strands of 1 ¾-inch foam material conforming to MIL-R-6130 (1), enclosed
and assembled in textured nylon duck conforming to MIL-C-43734 (2). Both ends of the belt are secured with 1-
inch binding tape conforming to MIL-T-5038 (4). 1½-inch web straps conforming to MIL-W-17337 (5) are sewn to
each end of the belt with male and female portions of a 1 ½-inch side release buckle conforming to P/N 150-1155
(6) threaded onto the ends. Two 1-inch nylon web straps conforming to MIL-W-43668 (8) are sewn horizontally to
the outside of the belt and bartacked at 1 ¼-inch intervals using Size E Thread conforming to V-T-295 (11) to
provide attaching points for pockets or pouches. Two web loops of 1-inch webbing (8) sewn to the top center of
the belt, approximately 6 inches apart, retain double bar buckles conforming to PD-02-02 (ITW #00648-09) (21).
Otherwise, the waistbelt is assembled using Size F Thread (10).
The lashing straps are 66 inches long and cut from 1-inch webbing (8) with 1-inch side release buckles
conforming to drawing 5-10-47 (81337) (12) threaded onto the ends. The lashing straps are not repairable items
and should be made as necessary.
The set, buckles (repair kit), contains four 1-inch side release buckles (12) and one 2-inch side release buckle
conforming to ITW P/N SR2-D (13). The buckles are not repairable items and the set should be requisitioned as
necessary.
The ALICE adapter clip is made of a 4-inch length of 3 ½-inch webbing conforming to MIL-W-17337 (14) with a 4-
inch length of 2 ¼-inch webbing conforming to MIL-W-4088 (15) sewn and bartacked at 1 1/4 inch intervals using
Size E Thread (11) on one side, and a 4-inch length of 1-inch webbing (8) bartacked at the center. Two double
strands of the same webbing with a 3 1/8-inch long polyethylene stiffener conforming to PD-02-02 (16) in each
are sewn to the top of the adapter clip. These attaching straps fold over and secure the adapter clip to a belt using
snap fasteners consisting of a button/socket conforming to MIL-F-10884 (17), and an eyelet/stud conforming to
MIL-F-10884 (18) that are held in place with an eyelet/washer combination conforming to MIL-E-20652/1B (19).
The ALICE adapter is not a repairable item and should be made as necessary.
The K-Bar Adapter adapts the current knife sheath to the MOLLE attachment system. It consists of a 4 ½-inch
length of 3 ½-inch-wide nylon webbing conforming to MIL-T-17337 (14). Two 1-inch-wide webbing straps (8) are
sewn to the top of the adapter and folded to enclose a 3 1/8-inch length of polyethylene (16). Snap fastener
eyelets/studs (18) are installed at the ends of the attaching straps. Corresponding snap fastener button/sockets
(17) are installed on the front of the pouch. A 4 ½-inch length of 1 inch-wide webbing (8) is bartacked to the back
of the adapter to form two attaching points. Two, 3 ¼-inch lengths of 2 ¼-inch-wide nylon webbing (15) onto
which 2 x 2 inch patches of hook and pile fastener conforming to MIL-F-21840 (20) are sewn, are bartacked, to
the nylon webbing at opposite ends. Eyelet/washer type eyelets (19) are installed onto the 2 ¼-inch web straps.
27-3. IDENTIFICATION AND DESCRIPTION - Continued